Aube Technologies TH146-P-2H1C Guida di Installazione Scaricare il pdf

TH146-P-DE 400-280-004-C 11/29/06 1/9

TH146-P-DE

Installation Guide

Programmable Heat Pump Controller

The TH146-P-DE programmable controller can be used to control a

heat pump system. The following devices can be connected to the

controller:

 heat pump

 auxiliary heating (furnace)

 air recirculation fan

 humidifier

 dual-register meter (dual energy)

 remote control device (for the unoccupied mode)

• CT280-HP-2H1C control module

• TH146-P console with two wall anchors and mounting screws

• AC144-03 outdoor temperature sensor (3 m or 10 ft) with

mounting clip (see section 2.7)

• RC845 relay (see section 2.5)

• AC146-410 plenum temperature sensor (see section 2.8)

• CT241 telephone controller (see section 2.10)

Install the control module on the furnace’s electrical panel, away

from the heat source.

Install the console in the area where you wish to measure the tem-

perature and humidity. Avoid locations where there are air drafts

(e.g., top of staircase or air outlet) or stagnant air (behind a door).

Do not install the console on a wall hiding air ducts nor expose it to

direct sunlight.

NOTE: If this controller replaces an existing thermostat, the wires

that were connected to the thermostat can be used to connect the

console. The maximum wire length is 30 m (100 feet).

1) Choose a location about 5 ft. (1.5 m) above the floor on an

inside wall.

2) Loosen the captive screw under the console.

3) Detach the console from its base by pulling the bottom section.

4) Secure the base using the wall anchors and screws.

5) Connect the console to controller terminals TH and TH (no

polarity).

Connect the heat pump to the controller as follows:

• Controller terminals R and C to heat pump terminals R and C

(see section 2.4)

• Controller terminal Y to heat pump terminal Y

• Controller terminal O/B to heat pump terminal O

• Controller terminal WW to heat pump terminal WW

TH146-P User Console

CT280-HP-2H1C Control Module

AC144-03 Outdoor

Temperature Sensor

1. Introduction

1.1

Applications

1.2

Supplied Parts

1.3

Accessories

2. Installation

2.1

Control Module (CT280-HP-2H1C)

2.2

User Console (TH146-P)

2.3

Heat Pump

1 2 3 4 5 6 7 8 9

Sommario

Pagina 1 - TH146-P-DE

TH146-P-DE 400-280-004-C 11/29/06 1/9TH146-P-DEInstallation GuideProgrammable Heat Pump Controller-The TH

Pagina 2

TH146-P-DE 400-280-004-C 11/29/06 2/9• Controller terminal L to heat pump terminal L • Controller termina

Pagina 3

TH146-P-DE 400-280-004-C 11/29/06 3/9NOTE: In this mode, the short-cycle protection is disabled and the i

Pagina 4 - Configuration Menu

TH146-P-DE 400-280-004-C 11/29/06 4/9Configuration MenuItem Parameters Display Options Default Descriptio

Pagina 5

TH146-P-DE 400-280-004-C 11/29/06 5/9Connection Diagram — New InstallationTH146-PAC144-03AC146-410CT241Hu

Pagina 6

TH146-P-DE 400-280-004-C 11/29/06 6/9Connection Diagram — Add-on InstallationTH146-P24 V TransformerDual

Pagina 7

TH146-P-DEUser’s GuideProgrammable Heat Pump ControllerTH146-P-DE 400-280-004-C 11/29/06 7/9n Press Clk.

Pagina 8 - Unoccupied Mode

TH146-P-DE 400-280-004-C 11/29/06 8/96.3.1 Manual AdjustmentUse this adjustment mode to set the temperatu

Pagina 9 - 10.Support

TH146-P-DE 400-280-004-C 11/29/06 9/9Manual AdjustmentIn manual adjustment, the humidity level is set by

Più documenti per Termostati Aube Technologies TH146-P-2H1C

Per vedere il documento Aube Technologies TH146-P-2H1C Guida di Installazione

Aube Technologies TH146-P-2H1C Guida di Installazione (11 pagine)

Commenti su questo manuale

Nessun commento

Aube Technologies TH146-P-2H1C Guida di Installazione

Navigare online o scaricare Guida di Installazione per Termostati Aube Technologies TH146-P-2H1C. Aube Technologies TH146-P-2H1C Installation guide Manuale Utente

Sommario

Più documenti per Termostati Aube Technologies TH146-P-2H1C

Commenti su questo manuale

Prodotti e manuali riguardandi Termostati Aube Technologies TH146-P-2H1C